The Purelux MF44 is a compact, multifunctional work light with a wide light pattern, which in addition to a bright white light is also equipped with an orange flashing light approved for road traffic according to the R65 standard. MF44 is intended to be mounted on the side of, for example, motorhomes, caravans, vans and trucks, or other work vehicles. When installed on work vehicles, the full capacity of the lamp can be utilized, for effective illumination of the immediate vicinity and side of the vehicle, and as an attention and warning light when working on a construction site or in traffic. Unlike traditional work lights with a wide light pattern, the MF44 can illuminate the sides of the vehicle significantly more effectively, as the lamp's lens is mounted at an angle of 45 degrees to the frame. Where a traditional work light directs the light straight ahead and leaves the side of the vehicle practically completely dark, the MF44 spreads its luminous flux of 3500 lumens evenly and widely into the surrounding environment, making it an exceptionally good light, e.g. too close work.
Thanks to the wide light pattern, only one lamp per side can be enough for smaller vehicles, but with the help of several lamps, the width and power of the light can be further increased, so that the surroundings of large vehicles can be illuminated, for example, during tasks that require precision and care. The lamp's dark profile allows for a neat installation, and its compact and graceful fixture makes the work light a unified piece and blends in to give the vehicle a unified look. The included white frame gives a nice fit even in bright vehicles.
MF44 are approved for road traffic according to standards R23 and R65, which means they can be used both as reversing lights and as warning lights in traffic. The Purelux MF44 has up to 13 different flash functions, from which you can choose the one that best suits your needs. For installing multiple lights, they can also be synchronized to work together or alternately. Complying with the highest protection class (IP69K), the MF44 lamps are completely dust and waterproof, even vapour-tight. The Purelux MF44 can handle any conditions that may arise, whether it's heat and humidity or extreme weather with rain and snow. Two year (24 month) warranty!
Content
Purelux MF44
Power cord (40 cm), no plug
White frame
Rubber mounting frame
Mounting screws
User and installation instructions (FI/SE/NO/DK)
Technical specification
Make and model: Work lighting Purelux MF44 32W, Wide
Area of use: As work lighting for vehicles/work machines
Operating voltage: 10-30V
Manufacturer's declared power consumption:
Side light: 2.66A @ 12V / 1.33A @ 24V
Warning light: 1A @ 12V / 0.5A @ 24V
The manufacturer's declared effect
White light: 32 W
Warning light: 12 W
Manufacturer's declared luminous flux:
White light: 3500 lm
Warning light: 2361 lm
Manufacturer's declared color temperature: 4500-5500K
Connection: No contact, straight wires
Cable length: 400 mm
Dimensions: 236 x 37 x 80 mm (W x H x D)
Distance between mounting holes: 190 mm
Protection class: IP69K
Approvals: EMC: ECE: R10, R23, R65XA1
Warranty: 24 months
Operating modes
Single flash (100% luminous flux)
Single flash (50% luminous flux)
Dual flash (100% luminous flux)
Dual flash (50% luminous flux)
Single flash (slow)
Triple flash
Fivefold flash
Low light
Single + (2) double flash
Single + (3) triple flash
Single + (5) quintuple flash
Continuous flash
Cruise (30% luminous flux)
Quick guide
Installation
Red: Power (+)
Black: Ground (-)
Yellow: Power (warning light)
Green: Operating mode selection / Synchronization / Reset
Operating mode selection: Connect the green wire to power (eg red wire) for less than 1 second to change the operating mode. Can be implemented with a power switch (the power switch is connected between the battery or other power source and the green cable)
Synchronization: Select the same operating mode on the lights you want to synchronize by energizing the green wire for less than 1 second. Then connect the green cables of the lights you want to synchronize with each other. In this way, the lamps flash in the same rhythm and change operating mode (all together) when the operating mode of a lamp changes. For alternative synchronization, see below.
Reset: Hold green wire to positive for more than 5 seconds to reset lamp to operating position #1
White: Alternate sync
Alternate Sync: With the power off, connect the white wire to the red wire for the lights you want to blink alternately.
